-------------------------------------------
فلتر المكيف | صنها بنفسك Toyota DIY - Duration: 1:36.
The air conditioning filter
must be cleaned or changed regularly to maintain air conditioning efficiency.
To remove the filter: Start the engine.
Switch air conditioning to "Recirculate Air" mode,
then then turn the engine switch off.
Open the glove box and remove the separate tray.
Remove the filter cover.
Remove the filter case.
To clean the filter blow compressed air through the filter from the downward side.
Hold the air gun 5 cm from the filter and blow for approximately 2 minutes
Do not clean the filter with water,
as doing so will cause damage to the system.
Make sure that the side marked "Up" is pointing up.
If air flow from the vents decreases dramatically,
the filter may be clogged.
Inspect, clean and replace the air conditioning filter
according to the maintenance schedule.
In dusty areas or areas with heavy traffic flow,
more frequent cleaning may be required.
To avoid possible damage to the air conditioning system,
make sure that a filter is always installed
when using the air conditioning system.
-------------------------------------------
Toyota DIY نظام التحذير | صنها بنفسك - Duration: 1:34.
The Theft Deterrent System is a security system designed
to sound alarms and flash the vehicle's exterior lights
if it detects a possible break-in.
The system is automatically activated
30 seconds after the vehicle's doors have been locked.
Audible alarms may sound, and exterior lights may flash, in the following cases:
When a secured door is being unlocked, or It is being opened by means
other than the vehicle's Smart Entry and Start System
or using the wireless remote control,
in which case the doors are relocked automatically.
When the engine hood/bonnet is opened.
When a window is broken
When a battery cable is disconnected and/or reconnected.
The alarm system is deactivated when:
The doors are unlocked using the Smart Entry and Start System
or the wireless remote control.
The engine is started.
Note that the alarm takes a few seconds to deactivate after the engine is started.
Avoid activating the Double Lock System
when there are people inside the vehicle.
Once activated, none of the doors can be opened from the inside the vehicle.
-------------------------------------------
تغيير بطارية المفتاح | صنها بنفسك Toyota DIY - Duration: 1:50.
Many people find it difficult to replace the wireless remote control battery
and resort instead to using the mechanical key for an extended period of time.
However, replacing the battery is quite easy.
Note that the remote's operational range will be reduced
and the Smart Entry and Start system will not function properly
when the battery is depleted.
To replace the battery, follow this procedure:
For wireless remotes with a Smart Entry and Start system:
Take out the mechanical key.
Use the tip of the mechanical key to pry open and remove the cover.
Insert a new battery with the "+" terminal facing up.
Put all the pieces of the remote back in their place.
For wireless remotes without a smart entry & start system,
follow this procedure:
Use a screwdriver to remove the wireless remote cover.
Remove the battery module.
Open the case cover using the screwdriver.
Remove the depleted battery and insert a new one
with the "+" terminal facing up.
Put all the pieces of the remote back in their place.
To ensure the proper operation of the
Always work with dry hands when handling the battery.
Do not touch or move any other component inside the remote control.
Do not bend either of the battery terminals.
-------------------------------------------
مستشعر المساعدة على الاصطفاف | صنها بنفسك Toyota DIY - Duration: 2:00.
Toyota parking assist-sensors
are designed to alert the driver to surrounding objects and obstacles
using warning buzzers and flashing indicators.
The buzzer sounds faster as the vehicle approaches an obstacle
until the buzzer sounds continuously.
A graphic is also automatically displayed
that informs the driver of the position and distance to the obstacle.
You may chose to either display the graphic of the car
on the multimedia display
or to display rear view monitor screen.
To turn the system on, press the switch.
Setting up Toyota parking assist-sensor:
Press the "SETUP" button on the multimedia system.
Select "Vehicle" on the "Setup" screen and select "TOYOTA Park Assist Settings".
Select the desired item:
Alert Volume. Turning the display on or off.
To set up the display and set tone indication.
Observe the following precautions
when using the Toyota parking assist-sensor:
Do not use the sensor at speeds in excess of 10 km/h.
The sensors' detection areas and reaction times are limited.
Do not install accessories within the sensors' detection areas.
If the message "Clean Parking Assist Sensor" is displayed,
clean the sensors.
If the message "Parking Assist Malfunction" is displayed
or a warning light comes on,
or if the indicator comes on continuously without a buzzer sounding,
have the vehicle inspected by your Toyota dealer.
-------------------------------------------
فحص الاطارات | صنها بنفسك Toyota DIY - Duration: 2:00.
Tire care is vital for safety.
Replace tires in accordance with maintenance schedules.
Check the tires for any indicators of wear, such as:
wear on the tire lining up
with the triangle molded into the sidewall of the tire.
The tread of the tire lining up with the treadwear indicators.
Uneven wear, such as excessive wear on one side of the tread.
Noticing any of these signs may require that the tire be replaced.
Rotating your tires approximately every 5000 km in the order shown,
equalizes tire wear and helps extend tire life.
When to replace your vehicle's tires:
Cracks on the tire deep enough to expose the fabric.
Bulges on the tire indicating internal damage.
A tire goes flat repeatedly.
Cases in which damage to the tire cannot be properly repaired.
For your safety and to maintain your vehicle's integrity,
observe the following precautions when replacing tires:
Do not mix tires of different tread patterns.
Do not use tire sizes other than those recommended by Toyota.
Do not mix differently constructed tires.
Do not mix summer, all season and snow tires.
Do not use tires that have been used on another vehicle.
Do not forget to install tire pressure warning valves and transmitters
when replacing tires.
-------------------------------------------
فحص أكياس الهواء | صنها بنفسك Toyota DIY - Duration: 0:59.
SRS airbags are a vital safety component,
therefore, it is imperative to have them inspected and/or repaired
in the following cases:
The front of the vehicle is slightly damaged or deformed.
A portion of a door or its surrounding area is damaged or deformed
due to a minor impact.
The area of airbag inflation is scratched, cracked, or otherwise damaged,
on the pad section of the steering wheel, the side portion of the instrument panel,
the surface of the seats, or roof side rail garnishes.
Contact your Toyota dealer as soon as possible
if any of the SRS airbags have been inflated.
-------------------------------------------
استخدام نظام مراقبة المنظر الخلفي الجزء الأول | صنها بنفسك Toyota DIY - Duration: 1:40.
The rear view monitor system
displays guide lines behind the vehicle to assists the driver while backing up.
The rear view monitor system will activate when the shift lever is in R,
and deactivates when the shift lever is in any position other than R
or when any button on the display is pressed.
Note that the rear-view camera has a limited viewing angle,
and any impact to it or foreign matter adhering to it
may obstruct its view or affect the clarity of the image it transmits.
The rear-view camera uses a special wide-angle lens.
The distance of the image appearing on the screen differs from the actual distance.
The distance guide lines give a distance guide for flat road surfaces
and cannot be used to measure distances
when there are protruding objects in its line of sight.
Rear view monitor system precautions:
Be sure to check that the parking space will accommodate your vehicle
before maneuvering into it.
Be sure to back up slowly, depressing the brake pedal.
Turn off the system
if you feel that there is an increased likelihood of a collision.
Take into account external factors that may affect the system's performance;
such as traffic conditions, road surface conditions, and vehicle condition.
-------------------------------------------
تنبيهات اكياس الهواء | صنها بنفسك Toyota DIY - Duration: 2:31.
SRS airbags are an integral safety component.
They work together with the seat belts
to help reduce the risk of death or serious injury.
To protect vehicle occupants, SRS airbags inflate
when the vehicle is subjected to certain types of severe impacts.
However, it is your responsibility to observe SRS airbag precautions.
The SRS driver airbag deploys with considerable force,
and can cause death or serious injury if safety precautions are not observed.
Place yourself at least 25 cm from the steering wheel
Do not sit on the edge of the seat, whether you are the driver or passenger,
so that the airbag points toward your chest instead of your head and neck.
The rear seats are safer for infants and children,
however, if your child is old enough to safely sit in the front passenger seat,
do not allow them to stand in front of the SRS front passenger airbag unit
or sit on the knees of a front passenger.
Do not attach any accessories to the seats, dashboard, or instrument panel.
These items can become projectiles when the airbags deploy.
Do not place anything on the front passenger seat that may cause
the passenger to sit higher than normal;
this may disrupt their weight distribution across the seat cushion,
causing inaccurate data to be sent to the airbag sensor assembly.
Do not subject the area of the SRS airbag components to impacts.
Doing so can cause the SRS airbags to malfunction.
Do not allow the front seat occupants to hold items on their knees.
The driver and all passengers in the vehicle
must wear their seat belts properly.
Open a door or window to allow fresh air in,
If breathing becomes difficult after the SRS airbags have deployed.
Consult your Toyota dealer before performing the following modifications:
Disassembly or repair of the SRS airbags,
the steering wheel, instrument panel, or dashboard.
Repairs or replacement of seats or seat upholstery.
Repairs or modifications of the front fender or front bumper.
Any other such modifications or repairs in or around the front end of the vehicle.
-------------------------------------------
تشغيل مساحات الزجاج | صنها بنفسك Toyota DIY - Duration: 3:26.
In this video, we will learn how to operate
the windshield and rear window wipers and washer.
Use the windshield wiper lever
to control the operation and speed of the wipers.
by moving it up or down.
To control the wipers, select one of the following operations:
Low speed operation.
High speed operation.
Temporary operation.
If you want to spray washer fluid, pull the lever towards you.
During intermittent operation,
you may set the interval for wiper movement
by rotating the circular selector on the wiper lever.
The rain sensor is an optical sensor
that determines the amount of rain falling onto the windshield.
The rain sensor may not operate properly
when sunlight or another bright light strikes the windshield
or if bugs etc. are present on the windshield.
The automatic rain-sensing mode is the default mode.
In this mode, the wipers are switched on and off, speeded up and slowed down
automatically in accordance with rain volume and vehicle speed.
When AUTO rain-sensing is selected,
the wipers will operate once to show that AUTO mode is activated.
You may adjust the sensitivity of the rain sensor
by rotating the selector ring on the wiper lever.
Vehicle speed affects the operation of the wipers when the washer is used.
Washer operation is delayed until after wiping to prevent dripping starts.
This applies to both AUTO and manual modes.
With low speed windshield wiper operation selected,
wiper operation will be switched from low speed to intermittent wiper operation
only when the vehicle is stationary.
If sensor sensitivity is set to maximum,
you won't be able to change the wiper operation.
When the wipers are set to AUTO operation,
take care that your fingers or anything else
does not become caught in the windshield wipers.
You may control the rear window wipers
by turning the end of the wiper lever.
Intermittent operation. Normal operation.
In the same way, you can activate washer/wiper dual operation
by pushing the wiper lever away from you.
Avoid using the wipers in the following situations:
When the windshield is dry, as this may damage the wipers and/or the windshield.
When the washer fluid tank is empty,
do not operate the switch continually
as the washer fluid pump may overheat and get damaged.
When there is no washer fluid spray from the nozzle,
the washer nozzle may be blocked
or the washer fluid tank may be empty.
If the washer nozzle is blocked,
do not try to clear it with a pin or other object.
The nozzle will be damaged.
-------------------------------------------
تنبيهات حول استخدام الونش الكهربائي | صنها بنفسك Toyota DIY - Duration: 1:38.
After using the winch observe the following precautions:
Stop the remote control switch when about 1 m of cable is left.
Secure the hook in place on the hook holder.
Hold the hook holder by the handle
and operate the remote control switch intermittently.
Install the hook holder in the winch opening.
Rewind the cable so that it is under slight tension.
Disconnect the remote control wire plug and install the dust cap on the terminal.
Install the winch cover.
Precautions for using the electric winch:
When first using the winch, some smoke may issue from the motor.
If the cable becomes tangled, pull it out by the hook,
then correctly rewind the cable.
When handling the cable, wear thick gloves.
When towing your vehicle using the winch,
avoid applying a load suddenly to the towing cable.
Avoid using deformed, frayed or worn cables.
Remember that the electric winch is vital for towing and dragging.
You must maintain it in good working order at all times.
-------------------------------------------
نظام الخروج عن خط السير | صنها بنفسك Toyota DIY - Duration: 1:44.
The Lane Departure Alert system (LDA)
uses a camera sensor to recognize visible white or yellow lines
and alert the driver when the vehicle might depart from its lane
This function operates when all the following conditions are met:
LDA is turned on.
Vehicle speed is approximately 50 km/h or more.
System recognizes white (yellow) lines.
Width of traffic lane is approximately 3 m or more.
Turn signal lever is not operated.
Vehicle is driven on a straight road or around a gentle curve.
To avoid LDA system malfunctions, observe the following precautions:
Do not modify the headlights.
Do not modify the suspension.
Do not install or place anything on the hood or grille.
If your windshield needs repairs, contact your Toyota dealer.
Conditions in which functions may not operate properly:
White (yellow) lines are are not clearly visible due to any reason.
The white (yellow) lines are disconnected or broken.
When driving on a winding road.
The traffic lane is excessively narrow or wide.
The vehicle is extremely tilted due to carrying a heavy load.
-------------------------------------------
انظمة استشعار تويوتا الخاصة بالسلامة | صنها بنفسك Toyota DIY - Duration: 3:02.
In this video, we will learn about the Toyota Safety Sense P,
TSSP helps reduce the impact to the occupants and the vehicle
in the case of a collision in normal driving conditions.
The system was designed to operate as a supplementary safety system
under the assumption that the driver will drive safely,
Toyota Safety Sense P is comprised of two sensors:
A radar sensor mounted located behind the front grille,
and a camera sensor mounted behind the windshield.
The system uses readings from these two sensors to operate a group of subsystems:
The Pre-Collision System (PCS).
Dynamic radar cruise control.
Lane Departure Alert (LDA).
Automatic High Beam (AHB).
To ensure the proper operation of the safety and driver assist systems,
observe the following precautions,
To avoid malfunction of the radar sensor,
keep the radar sensor and front grille emblem clean at all times.
Clean the radar sensor and front grille emblem with a soft cloth
so you do not scratch or damage them.
Do not attach any accessories or stickers to the sensors,
including transparent stickers.
Do not disassemble the radar sensor or front grille emblem.
Do not modify or paint the radar sensor, front grille emblem or surrounding area.
To avoid malfunction of the camera sensor and to ensure its proper operation:
Keep the windshield clean at all times.
Do not install an antenna or attach stickers, shades,
or other items to the area of the windshield in front of the camera sensor.
Replace the windshield if it is damaged or cracked.
Do not get the camera sensor wet or allow bright lights to shine into it.
Do not change the installation position or direction of the camera sensor.
Do not disassemble the camera sensor or modify
any components of the vehicle around the camera sensor;
such as the rear-view mirror or sun visors.
Do not install an electronic device or device that emits strong electric waves
near the camera sensor.
If the camera sensor is dirty or damaged, contact your Toyota dealer.
If you need to remove, install, replace, or paint
the sensor, front grille, or front bumper
contact your Toyota dealer.
If the radar sensor or surrounding area has been subjected to a strong impact,
have the vehicle inspected by your Toyota dealer.
-------------------------------------------
Toyota Avalon 2019 | 2019 Toyota Avalon - Safety and Driver Assistance Review - Duration: 3:40.
Toyota Avalon 2019
2019 Toyota Avalon
2019 Toyota Avalon Review
2019 Toyota Avalon Exterior
2019 Toyota Avalon Features
2019 Toyota Avalon Interior
2019 Toyota Avalon Seat
-------------------------------------------
Toyota DIY صنها بنفسك | EV Mode-وضع الدفع - Duration: 1:20.
The EV drive mode of the Prius hybrid
is a noiseless driving mode
that runs for short distances that range from a few meters to about one kilometre,
depending on the battery's charge level.
The system helps cut fuel consumption,
as the vehicle is powered only by the battery,
while the electric motor is used to drive the vehicle.
You may switch the EV mode on or off by pressing the "EV Mode" button.
Situations in which EV drive mode cannot be turned on:
Vehicle speed is high.
The accelerator pedal is depressed firmly.
The hybrid battery is low.
When driving in EV drive mode, pay special attention to the area around the vehicle.
Because there is no engine noise,
pedestrians or other people in the area may not be aware of the vehicle.
-------------------------------------------
تنظيف السيارة من الداخل | صنها بنفسك Toyota DIY - Duration: 1:52.
It is important to clean the interior of your vehicle periodically to protect it.
Toyota recommends cleaning the interior of the vehicle at least twice a year
to maintain the quality of the vehicle's interior.
When cleaning the interior of the vehicle, observe the following precautions:
Remove dirt and dust using a vacuum cleaner.
Wipe dirty surfaces with a cloth dampened with lukewarm water.
If dirt cannot be removed, clean it with neutral detergent
diluted to approximately 1%.
To clean leather surfaces:
Remove dirt and dust using a vacuum cleaner.
Make sure to wring out excess water before using the piece of cloth.
Use a cloth dampened with a diluted water solution of approximately 5% detergent,
to wipe any excess dirt and dust.
Wipe the surface with a dry, soft cloth to remove any remaining moisture.
Allow the leather to dry in a shaded ventilated area.
Shampooing the carpets:
You can use commercial foaming-type cleaners available
without the use of water.
Use a sponge or brush to apply the foam.
Rub in overlapping circles.
You can clean seatbelts
with mild soap and lukewarm water using a cloth or sponge.
-------------------------------------------
ايقاف السيارة في حالات الطوارئ | صنها بنفسك Toyota DIY - Duration: 1:49.
Only in an emergency, when it becomes impossible
to stop the vehicle in the normal way,
stop the vehicle using the following procedure:
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly
as this will increase the effort required to slow the vehicle.
Shift the shift lever to N.
After slowing down,
stop the vehicle in a safe place by the road.
Stop the engine.
If the shift lever cannot be shifted to N,
Keep depressing the brake pedal with both feet
to reduce vehicle speed as much as possible.
Stop the engine and turn the engine switch to the "ACC" position.
Power assist for the brakes and steering wheel will be lost,
making the brake pedal harder to depress and the steering wheel heavier to turn.
Therefore, decelerate as much as possible before turning off the engine.
Never attempt to remove the key, as doing so will lock the steering wheel.
To stop the engine in vehicles with a smart entry & start system:
Press and hold the engine switch for 2 consecutive seconds or more,
or press it briefly 3 times or more in succession.
Stop the vehicle in a safe place by the road.
-------------------------------------------
سائل تنظيف الزجاج | صنها بنفسك Toyota DIY - Duration: 1:07.
It is important to inspect the windshield washer fluid periodically.
Inspect the windshield washer fluid if any washer does not work
or the warning message appears on the multi-information display.
If the washer fluid warning indicator light comes on,
the washer fluid reservoir may be empty,
in which case you must add washer fluid.
Do not add washer fluid while the engine is hot or running
as washer fluid contains alcohol
and may catch fire if spilled on the engine,
and if spilled on any of the internal component inside the vehicle,
this may cause streaking on the vehicle's painted surfaces.
-------------------------------------------
حجرة الامتعة | صنها بنفسك Toyota DIY - Duration: 0:55.
Your vehicle's luggage compartment comes with a set of useful features.
Cargo hooks: Provided for securing loose items.
Raise the hook to use.
Always return the cargo hooks to their positions when not in use.
Storage compartment: remove the cover to use.
Make sure to keep the auxiliary box always closed to avoid damage or injury.
Warning reflector holder:
First-aid kit holder.
Do not allow children to climb on the luggage cover,
to avoid serious injury to the child or damage to the cover.
Không có nhận xét nào:
Đăng nhận xét