Auto news on Youtube Jun 29 2018

Hello and welcome to ZipperDetailing

Today I'm finally washing,

after a long time in the workshop, a really long time. 2 months!

So I'm washing my Toyota Supra.

Like I said it was 2 months in the workshop

And so a lot of

dirt has landed on the paint and it is hard to get it off.

I will show you !

Here you can see the paint on which all the

dirt has been collected.

I don't know if the camera can catch it,

it is not that easy with the red paint.

I will now do something which I normally don't,

I will scratch over it.

Perhaps you can hear how filthy the paint is.

I already tried to clean the car only with a pressure washer.

It is over the whole car.

If you look closely you can see the dirt on the black stripe.

Like I said, it is all over the car,

and it doesn't get rid with only water pressure.

Which means that we have to grab to harder actions.

So, I would say that we should begin

and show you how I'm cleaning the car.

The car is now completely washed.

Luckily I got rid of the dirt. It was really hard dirt.

I didn't have to use

the clay bar or even harder products.

The normal Carshampoo could dissolve it.

I will show you the endresult afterwards.

If you want to know more about the car itself,

I can make a video about it. Let me know in the comments what you think.

For the rest do I wish you a good day and until next time.

For more infomation >> Toyota Supra Hand Wash - With undertitles -Zipper-Detailing - Duration: 5:51.

-------------------------------------------

1997 Toyota Land Cruiser Thule Roof Rack Install/Overview - Duration: 7:40.

Hello in this video I'm going to be talking about putting some Thule bars on my

1997 Land Cruiser, so I currently have the factory rack up here

As you can see

It's a couple reasons

I want to replace this one is these boots here are rubbing away the paint and there's a little bit of rust here

So I could protect against that but I don't like this this rack. Anyway, another thing is I have a

Thule

Cargo carrier and when it's on here the back of it hits the rear spoiler

so what I've gotten here is the Thule Gutter High Foot, it's

387 and

I also have the I think these are LB65 load bars here

So I'll put this up on the car and you can see

The difference between this and the factory rack and I'll put a link in the description

To these items on Amazon if you use that

Length that I put there. That's my affiliate link

It helps me out a little bit and it kind of encourages me to make these videos. So

So this might be a little tricky to see

What I'll do is I'll Center this up a little bit so I have the factory load bar

and this is the Thule load bar so it sticks out I

Don't know. What about 10 11 inches there on either side. So they're quite a bit wider. So one thing

about these I

can I

Top kayaks also so with these I can use my stacker

I have a Yakima stacker here and I can put that on the load bar

You know somewhere and then you can stack one kayak on one side and then two on the other because you can technically stack four

kayaks, see if your load bars are wide enough. I only have three kayaks so

today, I only have three kayaks who knows what the future will hold but so I've got the

That there let's look at these

The foot the high foot

It comes with four obviously here

Comes with a heart or a bag. Let me open that I got that open

I also pulled the instructions out and one reason I went with the Thule is I like the quality of their stuff

you know, I have some other Thule things and

So that's what I want with there's a lot of options here if you wanted to do like the rooftop tent you could do

two sets of these these are

165 pound capacity

The factory

Now right here factory load bars are 100 pounds, so we're adding 65 pounds capacity to this

So and when you're looking at kayaks kayaks weigh

say, you know forty to sixty pounds that allowed me to add allow me to add another kayak into this so

I'm gonna read these instructions and I'll come back in a second. Okay, so I just glanced through these instructions

these aren't I'm not going to go over every step in instructions, but

what you do is you

Put the load bar in here. This does tilt for different angles and then you assemble it there's this clamp here

You run the bolt through back side

Through the clamp and then you put a washer and the knob on and this pivots here

And then on the car it looks kind of like this so these go on the rain gutter

Here the clamps on then you'll tighten this down. I don't have the load bar in there

I'll put the load bar in it'll clamp down on there and tightens

And then you can remove this plug here and put in a lock cylinder

So I don't have the lock cylinders right now for this

I'm going to order some that

Match my cargo carrier you can go on Thule's website and order them and you just use the key code

so what I'll do now is I'll put the

Load bars on and then I'll come back

Okay, so I've got the load bars installed here this is from the front of the vehicle and I'll

Go over here and show you some details

So it's it's good to have tape measure

So you can make sure everything's even

But from the foot here

To kind of the end is about 15 inches

Between the two load bars, I did 34 and this is all arbitrary, you know, that's just what I did

On top here we have it was right around 9 inches to the end of the bar and

The cap's on there so it's kind of hard to see but this was

This was a little less than 9 that just made them even

so and I positioned

My factory rack was at the very front and rear so I positioned this a little bit before

Towards the front of the car because like I say in my rack was too far back, although really since they're up higher here

Maybe that that probably wouldn't hit so and then these I moved these forward so next time I load

My roof rack or kayak I may

adjust these

You know forward or aft I don't know we'll see so and here I'll look at the height here

Here's the height or there's gonna be kind of hard to measure but

Looks like the factory rack was about 2 inches

To the bottom this is 5 so this is about 6 inches to the top. Let me get the factory rack here

So, yeah, the factory was probably two and a quarter

And this is

About five and a quarter. Let's try a better measurement so

quite a bit higher

So that's that I'm going to probably this is kind of a rubberized kind of grippy coating

I'm gonna put some 303 protectant on there. I'll put a link in the description to that too

And on any these plastic pieces these knobs and such

Just to help protect it from UV and then I'll eventually take my factory rack off

These here if I remember correctly are five millimeter

Bolts thread. So if I take these out

The holes will still be there. I'll probably get like a five millimeter round headed screw

And then maybe like a rubber gasket to seal them. Somehow hasn't quite figured that out

so, but if you have any questions

Please leave them in the comments if you haven't already I'd love you subscribe to my channel and thanks for watching. Bye